News
Sing Tao Daily Interview: BDC- Structural Health Monitoring System
Sing Tao Daily Interview:
BDC- Structural Health Monitoring System
【專題】深圳賽格啟示港樓 高齡摩廈須控「病歷」
深圳賽格大廈上月中多次震動,官方至今未得出事故原因。本港工程業界分析,大廈震動或受風力、施工質素,甚至是人為破壞樓宇結構引致,如大廈未設實時數據監測,將難以分析震動成因。縱然本港對新建樓宇的要求甚高,業界擔心,隨着樓高逾三十層的建築步入超過三十年樓齡,建築物保養及結構將為樓宇安全帶來新挑戰,一旦主力牆及鋼筋出現問題,稍強風力及環境震動,足以導致建築物大幅搖晃,甚至有倒塌危機,通過儀器實時監測樓宇安全,有其必要性。
自上月十八日起,賽格大廈出現多次震動,商戶及市民須即時撤離,有內地傳媒其後引述廣東省應急管理廳值班室的文件,表示專家初步認為震動由風、地鐵運行及溫度三方面因素造成。為查明原因,官方在六月一日起進行一系列測試,惟至今未公布結果。
港樓非鋼管混凝土結構設計
事實上,一八年颱風山竹襲港期間,不少港人都感受到大廈搖晃。香港工程質量檢測中心有限公司技術顧問趙雪美表示,樓宇震動源包括由地震、風、地盤打樁及地鐵運作引起環境震動,大廈內大型機器運作引起的機械震動,以及其他人為因素。施工質素及用料亦是另一成因,但由於無法取得賽格大廈的建築圖則,工程業界難以判斷工程水平。
實時監測數據可尋問題位置
目前工程界可通過實時監察系統,了解建築物結構狀況。趙雪美以賽格大廈為例,如大廈有裝設實時監察系統,便可在震動期間,收集建築物擺動速度、位移及頻率等,從而更準確找出事件起因。此外,系統亦可及早為大廈找出危機,她以一幢商廈為例,如有業主購入全層物業後將主力牆打通,一般難以察覺,惟主力牆受損,會影響建築物承受強風及震動的能力,而實時監察系統有能力從數據中找出發生大廈結構問題的位置,預防意外發生。
不過,本港目前僅有極少數摩天大廈採用實時監察系統,趙雪美指出,相關技術在外國已應用多年,並以新加坡為例,當地在一九八六年發生酒店倒塌事件,其後發現與設計有關,當地政府於是為政府興建的建築加設系統監察,避免意外重演。
Update of Building Diagnostic Consultants Limited (BDC) accreditation HOKLAS 140
Congratulations for the update of Building Diagnostic Consultants Limited (BDC) accreditation HOKLAS 140.
The concerned accreditation approves the technical competence of BDC for the performance of the following:
Calibration Services | Vibration measurements | Vibration monitoring device | Calibration of the acceleration, velocity and displacement |
Verification of Construction Materials Test Equipment | Cross-hole Analyser | Calibration of time interval of the main unit using a simulator |
|
Ultrasonic Drilling Monitor | Calibration of the time base frequency of ultrasonic signal | ||
Construction Materials | Adhesive | Pull-off test of mortar | In-house method DOC/TP17 |
Pull-off test of plaster | In-house method DOC/TP17 | ||
Pull-off test of render | In-house method DOC/TP17 | ||
Pull-off test of tiles | In-house method DOC/TP17 | ||
Concrete (Diagnostic) | Carbonation test | Hong Kong Housing Authority Materials Testing Services (2012/2014) for Maintenance & Building Materials - Specification Part D Cl. 4.3.1 (Method 1 & Method 2) | |
Covermeter survey | BS 1881: Part 204: 1988 | ||
Half-cell potential measurement | ASTM C876-91 | ||
Surface hardness measurement | BS 1881: Part 202: 1986 Cl. 6 | ||
Paint & varnish | Pull-off test of adhesion | BS EN ISO 4624: 2003, BS 3900-E10: 2003, Cl. 9.4.2 and Cl. 9.5 |